# Truss structures

## Background: Axially loaded truss element

A construction, which is made up of truss elements, is also called a *truss* or *truss structure*. A truss element can only be loaded axially, i.e. in the direction of the truss element. Under tension the truss element will increase in length as can be seen in {numref}`M-fig2_1` below.

```{figure-md} M-fig2_1
<img src="Media/Mentat/Mentat-fig2_1.png" width="600px">

Truss element lenght configuration
```

As a result of this extension, the truss element becomes a little thinner, which is called a transverse contraction. It is logical that this deformation depends to a large extent (but not only) on the properties of the material (rubber, wood, steel or you name it).

In FEM terminology we call a truss element in a truss an element. The truss elements in a truss are interconnected in points that can be conceived as hinges. In FEM terminology, such a hinge is called
a node. The attachment to the fixed world also takes place in the nodes.

When modelling a truss with Mentat, we have to specify exactly the spatial position of all nodes. We also have to indicate between which nodes elements are present. It will soon become clear that
it is useful not to define nodes and elements directly but via an intermediate step: the structure is first constructed from (straight) lines ((*line*) *curves*) and (*points*). The lines can then be divided into elements. It is emphasized that there is therefore a difference between *points* and *curves* on the one hand and *nodes* and *elements* on the other.

The construction must, as mentioned earlier, be connected to the fixed world. This must be done in such a way that rigid movement (translation and rotation) is excluded. We must therefore suppress
the movement of a number of nodes. These suppressed movements (*fixed displacements*) are called boundary conditions and kinematic boundary conditions. The load acting on the truss is modelled as forces (*point loads*), applied in nodes. These are called dynamic boundary conditions.

Of essential importance for modelling is the resistance of the material to deformation under the influence of an applied load: the stiffness. Material parameters that characterize the stiffness of the material are the modulus of elasticity or *Young’s modulus* $E$ and the *Poisson’s ratio* $\nu$.

The resistance to deformation of a truss element is determined not only by the elastic modulus $E$, but also by its dimensions. When a tensile bar is loaded with an axial pulling force $F$ , the extension $\Delta l$ is inversely proportional to $E$, inversely proportional to the cross-sectional area $A_0$ and proportional to
the length $l_0$. There is:

$$
\Delta l = \frac{l_0}{E\, A_0} F.
$$ (eq1-M)

Due to the elongation of the truss element will become thinner. If the truss element is circular-cylindrical, the diameter change applies $\Delta d $:

$$
\frac{\Delta d}{d_0} = -\nu \frac{\Delta l}{l_0},
$$ (eq2-M)

where $d_0$ is the original diameter. In general, the diameter change is very small, so that the cross-sectional area in the deformed state is approximately equal to the undeformed cross-sectional area:
$A \approx A_0$.

It is customary to use the axial strain ε and the strain in perpendicular direction εd as a measure of the deformation:

$$
\epsilon = \frac{\Delta l}{l_0} \quad \textrm{and} \quad \epsilon_d = \frac{\Delta d}{d_0}.
$$ (eq3-M)

As measure for the axial load we use axial stress $\sigma$:

$$
\sigma = \frac{F}{A} \approx \frac{F}{A_0}.
$$ (eq4-M)

From this equation it automatically follows that the elasticity modulus $E$ describes the relation between axial strain and axial stress:

$$
\sigma = E\, \epsilon.
$$ (eq5-M)
